Providing ** PARTS and SERVICE ** for Strippit/LVD turret punch presses. Please call 716-830-4630 for assistance
Cart 0

S machine J Frame

The S Series machines machined in 2 pieces the permanently joined to become one piece J framed machines.  These machine utilized the 33 station turret, and the 2 servo auto index was a superior design. Considered by many as a reliable, we'll designed workhorse.  Parts support is good, and there were a few variations, 40", and 50" throats, and 65", and 80" X travel designs.  The machine utilized 3 different controllers over the years. Fanuc OPB and OPC, and a few PC controlled machines also shipped.  The PC machines are to be avoided because of an obsolete, unsupportable Strippit® controller.

 

Common Part List

*Select link to go to product

Sensors

Shot Pin Sensors   

Strip Sensor

Press Drive Sensors

Work Clamp Scan Sensor

Work Clamp Protect Small and Large Sensor

X,Y Limit Sensors

Turret Slow/Reference Sensor Early Machines

Turret Reference Sensor Later Machines

Reposition Cylinder Sensor

Auto Index Engage/Disengage Sensor

Index Station Recognition Sensor

Work Clamp Closed Sensor

Hood Door Closed Sensors

Toolring Open Sensor

Drop Door Sensor

Press Drive Oil Level Switch

Airline Disengage Sensor

Work Clamp FootSwitch

Multitool Retracted Switch Long Tool

Multitool Retracted Switch Short Tool

Green Cycle Start Button

Yellow Mushroom Side Gauge Button

Servomotors

X Axis Servomotor

Y Axis Servomotor

T Axis Servomotor

C Axis Servomotor

Air Cylinders

Reposition Cylinder

Shot Pin Cylinder

Multitool Cylinder Short Tool

Multitool Cylinder Long Tool

Work Clamp Cylinder

Side Gauge Cylinder

Auto Index Brake Release Cylinder

Auto Index Engage Cylinder

Solenoid Bank Complete

Single Position Solenoid

Double Position Solenoid

Work Clamp Parts

Lower Jaw

Upper Jaw

Gauge Block

Work Clamp Body

Workclamp Height Spring

Linear Bearing

Work Clamp Target

Work Clamp Ratchet Handle Metric

Work Clamp Ratchet Handle Inch

Work Clamp Wedge Plate

Work Clamp Mounting Plate

Work Clamp Link Pin Assembly

Turret Parts

3-1/2" Bushing

1-1/4" Bushing

Auto Index Bushing with gear

 


CNC 2712

Accumulator Hyd. C/B

(Replaces Strippit® Part 802504-000)

(replaces Strippit® Part 802494-000)

$1,126.00
CNC 2705

Seal Oil Hyd C/B Internal, set of 2

(Replaces Strippit® Part Number 802497-000)

$53.00
CNC 2620

Cylinder (Shot Pin Sub Assembly) retrofit kit

Replaces Strippit® Part Number 800486-000

requires 4 pcs.



From $252.00
$683.00
CNC 1844

Lifter 1.25 reconditioned

(Replaces Strippit® Part Number 107747-000)

$160.00
CNC 3756

Memory Board Fanuc OPC

replaces Fanuc A16B-2201-0103

From $1,296.00
CNC 3291

PMC M BOARD FANUC OPB

(Replaces Fanuc® Part Number a16b-1211-0901-07a)

From $1,025.00
CNC 2965

Spring Workclamp

(Replaces Strippit® Part Number 1000744-000)

$29.00
CNC 2801

Sensor Proximity NO PNP 12mm includes extension cable

Replaces Strippit® Part Number 803318-000

Replaced by Strippit® Part Number  800503-000

replaces Strippit® 1000503-000

$231.00
MH6SCP-46

Body Workclamp UPPER 2 piece ( includes metric, and inch hardware)

This is the UPPER BODY ONLY.  You will also need a lower body, see  MH6SCP-47

If you only need the lower body see my part number MH6SCP-47

(Replaces Strippit® Part Number 119896-200)

From $936.00
CNC 1246

Lifter Spring S 1-1/4

(Replaces Strippit® Part Number 17591-000)

From $9.00
Request quote at Parts@CNCMachineryLLC.com
CNC 3162

Retainer Washer Hyd C/B

(Replaces Strippit® Part Number 802994370)

210349

$47.00
CNC 2711

Brake Disk lined Hyd C/B  Good Used Sold individually

Replaces Strippit® Part Number 802503-000

 We sell them individually for your convenience.  Keep in mind the outer disk in the PAK is normally ground to adjust the thickness of the PAK.  Do not replace this without grinding to makeup original thickness.  Typically just replace worn disks within the PAK or pads that have been damaged.

From $288.00
CNC 1932

Bumper X -Y Axis 38 mm

(Replaces Strippit® Part Number 119490-000)

$107.00
Request quote at Parts@CNCMachineryLLC.com
CNC 1178

HugNut Ballscrew Motor End

(Replaces Strippit® Part Number 16372-000)

$23.00
CNC 3282

Motherboard OPB

(Replaces Fanuc® Part Number A16B-1010-0285-15B)

$1,583.00
CNC 3288

Sub Cpu OPB

(Replaces Fanuc® Part Number A16B-1211-0320)

From $1,368.00
CNC 3324

Bulb OP #388. pkg. of 10

Replaces Strippit® 0023053-000

(Replaces Fanuc® Part Number A55L00010042)

$36.00
CNC 2599

Angled Flat Cage Assy. Auto

(Replaces Strippit® Part Number 800175-400)

$652.00
$878.00
CNC 5500

Clutch Plate Alignment Kit

 

From $720.00
CNC 4196

Pump Group HYD C/B Main 1000PSI

contains both pumps, coupled together

rebuilt must return core

replaces Strippit® 802994-050

$4,174.00