Parts For Strippit / LVD® Fabrication Equipment. CALL 1-888-879-5906
Cart 0

R,XP Machines

The low cost C Frame machine was introduced in the early 1990s.  This machine was a 20 ton, 20 station machine  with option of up to 3 Auto Index stations.  Most used a Macintosh controller, many were later refit with a Fanuc controller for improved reliability.  They were produced in 40" and 50" throat design with XP (extra performance) variations, and also a 1250H, a bridge frame variation using a hydraulic ram for punching.

 

Common Part List

*Select link to go to product

Sensors

Shot Pin Sensors   

Strip Sensor

Press Drive Sensors

Work Clamp Scan Sensor

X,Y Limit Sensors

Turret Reference Sensor

Reposition Cylinder Pressure Sensor

Auto Index Engage/Disengage Sensor

Auto Index Brake Sensor

Work Clamp Closed Sensor

Front Door Closed Sensor

Work Clamp FootSwitch

Multitool Retracted Pressure Switch

Green Cycle Start Button

White Cycle Stop Button

Red All Hold Button

Yellow Side Gauge Button

Red Emergency Twist Button

Controller

Motion Board Nucontrol 900

Motion Board Nucontrol 5100

NuBus Adapter Board SI computers

Servo Extender Card

Replacement Screen for Macintosh

Reliance Servo Amp XY with Analog

Reliance Servo Amp Original Style

Reliance Servo Amp New Style

Reliance Servomotor

Air Cylinders

Reposition Cylinder

Shot Pin Cylinder

Multitool Cylinder Short Tool

Multitool Cylinder Long Tool

Work Clamp Cylinder

Side Gauge Cylinder

Auto Index Brake Release Cylinder

Auto Index Engage Cylinder

Bimba Solenoid Bank Complete

Bimba Single Position Solenoid

Bimba Double Position Solenoid

Clutch Brake Hydraulic Solenoid

Work Clamp Parts

Workclamp Complete

Lower Jaw

Upper Jaw

Jaw Pack

Work Clamp Body

Work Clamp Ratchet Handle Metric

Work Clamp Ratchet Handle Inch

Turret Parts

3-1/2" Bushing

1-1/4" Bushing

Auto Index Bushing with gear

 

 


CNC 5500

Clutch Plate Alignment Kit

Includes alignment fixture critical to reassembling the CB unit, seals, o-rings, extra clutch and brake pads, new clutch disk, brake disk, and all necessary parts to reassemble the unit.  Contents are inventoried prior to ship, then rechecked when coming back.  You will be credited the difference in actual used after

We will subtract the $250.00 WEEKLY rental charge for the fixture.  Please keep in mind it is the only fixture I have and others need it as well.  Initial charge of $1000.00 will be credited when undamaged fixture is returned.

1 seal - CNC 2706 / 1 - hub retainer kit / 4 seals - CNC 2705 / 8 springs - CNC 2751 / 2 retainer washers - CNC 3162 / 2 locking bolts - CNC 2757 / 1 seal - CNC 2763 / 1 20 ton clutch plate - CNC 2826 / 1 30 ton clutch plate - CNC 2747 / 6 clutch pads - CNC 3828 / 1 brake plate - CNC 2708 / 4 SHCS - CNC 2753/ Fixture

$ 1,000.00
Sold Out
CNC 2124

Workclamp R,H20 series Lower Jaw

(Replaces Strippit® Part Number 120768-000)

$ 24.00
CNC 2112

Workclamp R,H20 series Body

(Replaces Strippit® Part Number 120531-000)

$ 180.00
CNC 2711

Brake Disc Pack Hyd C/B  Good Used

20 ton and 30 ton Brakes require 6 lined disks for the brake, 8 for the clutch. I sell them individually, to keep the price down.  Most times only 1 or 2 are needed.

Replaces Strippit® Part Number 802503-000

From $ 200.00
CNC 1842

Coupler AI Flex

(Replaces Strippit® Part Number 107727-100)

From $ 125.00
CNC 2668

Switch Micron Unit - Refurbished closes every 30 turns

Units include adjustment instructions critical to proper operation.

(Replaces Strippit® Part Number 802029-000)

$ 1,150.00
CNC 1610

Bushing 1-1/4 Turret

(Replaces Strippit® Part Number 100230-000)

$ 159.00
CNC 2662

Sensor Proximity Limit Switch (Replaces Strippit® Part Number 801721-000)

Includes Extension Cable

This is a more expensive universal sensor.  If you are not using this for a turret home switch, buy the cheaper normally open sensor.  Consider purchasing more than one, as Strippit® used many of these on their machines.

From $ 140.00
CNC 2176

Workclamp R,H20 series upper Jaw

(Replaces Strippit® Part Number 120372-000)

$ 187.00
CNC 4046

Servo Amplifier Reliance DM30 with Analog Board

replaces Reliance® 91011303

$ 1,850.00
CNC 3970

Amplifier Reliance DDM-030 Used on XP PC control Newer

Part Number 9101-1396

$ 1,250.00
CNC 2712

Accumulator Hyd. C/B

these accumulators are rebuildable

Must be charged to 600 PSI, we do rent a charge kit for $50.00 per week.  you will need a small bottle of Nitrogen.

(Replaces Strippit® Part 802504-000)

(replaces Strippit® Part 802494-000)

$ 625.00
CNC 3162

Retainer Washer Hyd C/B

(Replaces Strippit® Part Number 802994370)

210349

$ 32.00
CNC 2705

Seal Oil Hyd C/B Internal 2 Req

(Replaces Strippit® Part Number 802497-000)

$ 18.40
CNC 3097

Pin Link R Work Clamp

(Replaces Strippit® Part Number 8203212-000)

$ 20.00
CNC 2159

Workclamp R,H20 series Standoff NPZ Target

(Replaces Strippit® Part Number 121646-000)

$ 27.00
CNC 2657

Sensor Proximity NO PNP

Typically used for STRIP SENSOR, and some door switches

(Replaces Strippit® Part Number 801608-000)

$ 140.00
$ 153.00
CNC 2852

Ratchet Handle Workclamp Metric

Handle is manufactured from stainless steel to last longer. The orange handle signifies a metric thread, and also brings attention to the handle if the operator leaves it loose.

When ordering please verify you are ordering the correct thread.  Strippit used both SAE, and Metric and the parts manual may not be correct

(Replaces Strippit® Part Number 803563-000)

$ 22.00
CNC 2085

Workclamp R,H20,XP This clamp does not include protect zone target.  This is a universal clamp for all 20 TON R style machines.

Includes cylinder, and fitting.  Machined to match all inventory.

(Replaces Strippit® Part Number 121981-000)

$ 975.00
CNC 4244

Coupling Insert

replaces Strippit® 1002136-200

$ 48.00